The Industry's #1 Resource





Cooler more powerful intake charge for improved engine performance

Avon Lake, OH (October 26, 2016)…DEI’s CryO2 Intercooler Sprayer Kit harnesses the super cooling cryogenic properties of CryO2 to dramatically lower intake charge temperatures for more horsepower at lower long term cost than nitrous. Less expensive to purchase and refill than nitrous, this cost effective alternative for a boost in HP can be used for any vehicle including diesels that could use more power for the buck. A non-invasive system, it enhances the thermal transfer ability of the intercooler to lower air temperatures as much as 35% and as low as 50°F.

For turbo or supercharged systems, the sprayer mounts directly to the front of the intercooler and vents CO2 directly onto the cooling fins. The system can be configured to be activated by either a full WOT micro-switch, or controlled manually with a momentary push button. The complete bolt-on kit now offers an optional CryO2 adjustable duration timer switch (Part # 080203) for automatic on/off pulsing and a water sprayer kit (Part # 080140) for even greater I/C efficiency. 

CryO2 Intercooler Sprayer kit includes:

  • 10 lb. tank and mounting brackets
  • Cryogenic solenoid valve
  • 14 ft. stainless steel braided supply line
  • Full WOT and arming switches with momentary push button
  • CO2 fittings and electrical hardware
  • 16” x 5” front-mount intercooler sprayer and hardware
  • Stainless steel zip ties

For more information about Design Engineering’s Intercooler Sprayer Kit (Part # 080108) and complete line of CryO2 products, visit www.DesignEngineering.com, call DEI at 800-264-9472 or e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.. To review the product first-hand at the 2016 SEMA show stop by booth number 20013, or at PRI visit booth #1734.

Avon Lake, Ohio (March 23, 2016) -- Design Engineering, Inc. has announced the company’s inaugural Cruise-In car show planned for Saturday, June 18 at the company’s headquarters at 604 Moore Road, Avon Lake, OH. DEI is located three miles from Interstate 90.

The event begins at 10 a.m. and concludes at 3 p.m. This show will bring some of the area’s most exciting custom cars and hot rods to DEI as part of the 2016 Cruisin’ Times Lucky 7 Road Show.

“DEI is very excited to host this custom car show at our facility. In the past we enjoyed hosting a stop for race cars and drivers who were competing in the annual Tire Rack’s One Lap of America and invited the local community and media to visit the event at the DEI facility," said Tom Miller, DEI’s V.P. of Marketing and Sales "That event was so successful that we wanted to develop more events that will allow DEI to share our passion with others.”

A 50/50 raffle will be held during the Cruise-In to benefit the Friendship Animal Protective League in memory and deep respect for Ken Moore, a prior DEI employee who lost his battle with cancer in February.

The DEI Cruise-In will include music provided by Its Show Time D.J. services, great barbeque with all the fixin’s can be purchased from Jones Bones BBQ, raffles, DEI T-shirts and hats will be for sale and a scratch and dent sale area will be open.   

A rain date has been set for Sunday, June 19 in the event of inclement weather. Admission and parking is free for this public event.

For more information about DEI’s Cruise-In event, visit www.DesignEngineering.com, call 800-264-9472, or e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.. To keep up with the very latest DEI Cruise-In announcements, connect with DEI at Facebook.com/DEIcruisein.

Avon Lake, Ohio (April 13, 2016)…DEI’s Exhaust Wrap Kit is designed to wrap a set of small block or V-6 headers in one package. The kit includes two rolls of 2-inch by 50 ft. wrap designed to protect up to 1500° F, one can of HT Silicone Coating that coats, protects and preserves the wrap after installation, and eight 8 inch and four 14 inch 304 Stainless Steel Locking Ties to ensure long-lasting durability and hold. A free Locking Tie Tool is included to lock the ties tight and works with any ¼” drive. DEI’s stitched-in wrap guide line protects against overlapping for a professional and tight fit.

"Easy to install," this kit is recommended to use whenever there is a need to reduce underhood temperatures, improve exhaust flow, or protect against potential burns to arms and legs such as on motorcycles, ATVs or UTVs, according to the company.

DEI now offers its popular all in one kit in multiple combinations of wrap color and silicone coating colors including: tan wrap and white coating (#010091), tan wrap and aluminum coating (#010093), and black wrap and black coating (#010094).

For more information about DEI’s Made in the USA Exhaust Wrap Kits, visit www.designengineering.com, call 800-264-9472, or e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.. To keep up with the very latest DEI product introductions and company news connect on Facebook, Twitter and Pinterest, or subscribe to DEI’s You Tube channel.

Protects starters and other components from the damaging effect of heat soak.

Avon Lake, Ohio (May 4, 2016) -- Constructed of an aluminized heat reflective material backed with a high temperature rated glass fiber insulation barrier, the new mini DEI Versa Shield™ protects starters and other components from failure due to heat soak. Capable of reflecting radiant heat up to 2000°F and direct heat up to 500°F, this thermal product installs easily and can be trimmed to size.

Its convenient hook and loop closure design allows the shield to wrap around the starter and attach in minutes. Most starters will not require removal. Simply wrap the starter with the aluminized side out, trim length to fit and secure the edges by pressing the black loop material sewn into the material into the sewn in strip of black hook material.

Developed with a universal design to fit most mini sized starters (5.25” wide x 16.5” long) the shield is also ideal for multiple components where heat can affect performance—master cylinders, distributors, fuel pumps and more.  

For more information about DEI’s Made in the USA Versa Shield (part # 010384), visit www.DesignEngineering.com, call 800-264-9472, or e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

Avon Lake, OH (June 14, 2016)…Design Engineering’s Stainless Steel Positive Locking Ties are now available. The kits are designed for high heat applications such as exhaust wrap.

DEI’s Positive Locking Ties are made of 316 stainless steel in a ladder-style design with a ratchet tightening system and low profile clasp. Made for high heat applications, the ties can withstand heat in excess of 2500° F. Resistant to abrasive chemicals, the ties also can be used to secure electrical wires, cables, hoses and fluid lines.

DEI now offers a free Locking Tie Tool with the purchase of its Positive Locking Tie Kit (part #010219). The kit includes eight 9” x 8mm and four 14” x 8mm stainless steel ties and one Tie Tool.

For users not experienced with DEI”s stainless steel ties, or professionals that are accustomed to using the ties frequently, the DEI Locking Tie Tool is a major timesaver that will consistently provide professional results. To use, slide the tool on the end of any ¼” nut driver, engage the tie, and twist. DEI’s Locking Tie Tool fits on the end of any standard ¼” drive and works with all popular styles of stainless ties - up to ½” wide.

The DEI Locking Tie Tool is made of hardened steel and is black oxide coated for years of trouble free use.

To learn more about DEI’s complete line of thermal control products call 800-264-9472, visit www.DesignEngineering.com, or email This email address is being protected from spambots. You need JavaScript enabled to view it.. Keep up with the very latest product developments and company news for DEI on Facebook and Twitter, or subscribe to DEI’s newsletter.

Design Engineering has released Titanium Protect-A-Boots, which are a longer 8” length. DEI’s Titanium Protect-A-Boots provide maximum thermal protection against heat generated from the engine block, exhaust manifold and headers. Excessive heat may cause wires and boots to burn, harden or crack resulting in arcing, misfire or full ignition failure.

Constructed from heat resistant pulverized lava rock material, stranded and woven into a double-wall weave, these durable 8” boot protectors are resistant to chemicals, abrasions and contaminants. With the capability of withstanding direct heat up to 1800°F and radiant heat to 2,500°F, they provide effective protection for any high performance engine. Originally designed for the General Motors LS series of engines, the longer length and no-ring construction provides greater protection for street, race or off-road applications.

This new product from DEI is now available for purchase in either a two-pack (part #010543) or eight-pack (part #010544) set. The 1” I.D. and flexible construction allows for easy installation for straight or angled boots including Corvette C5 (1997-2004) and  C6 (2005-2013) generation models.

For more information on Design Engineering’s new 8” Titanium Protect-A-Boots or other thermal protection products, please visit www.designengineering.com, call 800-264-9472 or e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it..

Company is aggressively seeking reps and retailers; will provide comprehensive tools and resources

AVON LAKE, OHIO – June 6, 2016 (MEDIAWIRE) – Design Engineering, Inc. (DEI), foremost developer of thermal tuning and sound control solutions for the automotive aftermarket, announced that it has begun a campaign to better engage with and support specialist retailers in the mobile electronics industry. The goal of the campaign is to enable retailers and technicians to provide enhanced audio vibration control through use of the company’s Boom Mat line of sound-damping products.

As part of the campaign, the Avon Lake, Ohio–based manufacturer is expanding its sales reach with active recruitment of manufacturers’ representatives across the United States and Canada. Through these reps, the company plans to sign mobile electronics retailers to direct accounts, giving them access to the full Boom Mat line as well as its entire catalog of automotive aftermarket products. DEI will also proactively reach out to industry professionals and media with timely product and technical information.

“We are making a strong commitment to the mobile electronics community,” said Mike Zenone, Boom Mat brand manager. “We have a very solid history in the broader automotive aftermarket, and feel our strength is having the most complete product line available for retailers. We look forward to engaging with store owners and installers and showcasing the unique benefits of the Boom Mat brand.”

The Boom Mat line has been improved this year with the introduction of Boom Mat XL damping material. At 4mm thick, it provides superior noise damping while remaining flexible enough to adhere to irregular surfaces. The complementary Boom Mat Spray-On is ideal for reducing unwanted vibration in hard-to-reach areas. The company has also introduced the vehicle-specific sound-deadening headliner for the Jeep Wrangler, with two complete kits covering hard tops from 2007 to 2015.

To support installers, DEI is creating a technical support group through its Facebook page to address questions about application and selection of Boom Mat products for specific installs. The company will continue to expand its online video library to instruct installation technicians as well as promote the benefits of sound-damping and insulation products to consumers.

Retailers and manufacturers’ representatives who are interested can contact Mike Zenone at (800) 264-9472 or This email address is being protected from spambots. You need JavaScript enabled to view it.. Product information can be found at www.boommat.com

The Magazine

Magazine Quick Links







Copyright - Mobile Electronics Association 2020